.. ..
paypal

Injector & Glow Plug Removal & Repair Tools

          Pichler - Engine specific Injector Removal Tools 

Note all of the following Injector removal tools are listed alphabetically in engine brand order and then in engine size smallest to largest

Examples of engines fitted to different brand cars:
Alfa Romeo = Alfa Romeo
BMW = BMW, Landrover, MG-Rover, Mini
Fiat = Fiat, Alfa Romeo, Lancia, Opel, Saab, Suzuki
Ford = Ford, Mazda, LDV, Jaguar
Opel = Opel, Vauxhall, Chevrolet, Daewoo, Saab
PSA = Peugeot, Citroen, Mini, Ford, Mazda, Volvo, Landrover, Jaguar, Suzuki
Renault = Renault, Nissan, Opel, Dacia, Suzuki

As you can see there are a great amount of variations so it is important to know your engine brand type and engine code when looking up your injector removal tools.

Any of these sets that use the hydraulic piston will also need a hydraulic hand pump - see part no 271004000
Extraction Type : Hydraulic (This only applies if you have the Hydraulic attachments or purchase them separately or if they are included in the kit that you are purchasing)


60383305.._(Small).JPG 

Part No : 60383305 €1340 + vat
Complete set for removing seized injectors on PSA engine vehicles, 30 piece set including 20 tonne hydraulic piston (this is a different piston than in all other sets)
Extraction Type : Hydraulic or Mechanical
Makes: Citroen, Peugeot, Suzuki, Fiat
Engine Sizes: 2.0, 2.2 HDi
Engine Codes:
DW10ATED4 / RHS, DW12TED4 / 4HX
See bottom of page for demo video 

 

  

60385095_(Small).JPG 

Part No : 60385095 €1290.00 + vat. Does include hydraulic piston
Part No : 60385105 €971.00 + vat. Does not include hydraulic piston
Set for removing seized injectors on Renault engine vehicles. For both Bosch Pizo and Bosch coil type injectors. Also included in set are parts alowing you to remove nozzle and nozzle holder from the cylinder head if it breaks off when removing the injector.
Extraction Type: Hydraulic
Makes: Renault, Nissan, Opel
Engine Sizes: 2.0, 2.3DCi
Engine Codes: M9R, M9T
See bottom of page for demo video  

 60385190_(800x600).jpg Part No : 60385190   €390.00 + vat
M9R injector extraction supplementary kit.
This kit is to be used in conjunction with the above injector removal set and is required when the injector pulls out but snaps off below the sleeve. This set allows you to tap and pull the sleeve separately and then with the cutting heads and guide will allow you to machine out the injector bit by bit.
Makes : Renault, Nissan, Opel
Engine Sizes: 2.0, 2.3DCi
Engine Codes: M9R, M9T

  • Huge range of spares in stock for Pichler injector removal sets  please enquire.      

Universal Injector Removal Tools

 ADS4_(Small).JPG

Part No : ADS4  €245 + vat
Brand : A.D.S
Heavy duty 15kg sliding hammer.
Includes :
Adaptor for Bosch coil type injector
Special allen key for removing valve.
Adaptors also available for Bosch Piezo, Delphi, Siemens, Siemens Piezo and Denso Injectors.      

311026000_(Small).JPG  Part No : 311026000 211.55 + vat
Brand : Govoni
Universal Injector removal tool for removal of seized Injectors with adaptors for Delphi and Bosch Injectors
Adaptors also available for Siemens, Siemens Piezo and Denso Injectors. See below.

311185000_(Small).jpg  Part No : 311185000 €612.00 + vat
Brand : Govoni
Universal Injector removal tool for removal of seized Injectors with adaptors for Delphi, Bosch and Siemens Injectors
Adaptors also available for Denso Injectors. See below. 
Enquire for full details and instructions. 

 311166000_(Small).JPG

Part No : 311166000  with Piston €1331.50 + vat
Part No : 311166010 without Piston €1035 + vat
Brand : Govoni 
Universal set for removing seized injectors on a huge range of vehicles where the engines are flat top ie multi valve twin cam diesel engines where the injectors are fitted down in the middle of the head. Works on Bosch, Delphi, Denso and Siemens injectors.
Here is a short list of the engines it will work on
PSA 1.4 & 1.6 HDI
Fiat JTD 16 valve all sizes
Ford 2.2 & 2.4 TDCI
Renault 2.0 & 2.2 DCI, M9R & M9T
And many more
Optional upgrades
Part No : ADS0001011  €110 + vat
Special double grip adaptor for Bosch Piezo injectors for Renault 2.0 DCI M9R & M9T 
Part No : ADS7 €498 + vat
Solution for removing Bosch Piezo and Bosch coil type injectors when the top is broken off or when it leaves the nozzle holder behind in the head. For Renault 2.0 DCI M9R & M9T
Includes :  
Special twist socket
Blank for hole in cylinder head
Blank insertion rod, M16 x 1.5 long tap
M16 x 1.5 spiral flute tap and extension
M17 x 0.75 long tap
M16 x 1.5 special rod
M17 x 0.75 special rod
Tap extension

Extraction type : Hydraulic or mechanical 
See bottom of page for demo video
 

 6038424_(Small).JPG          Part No : 6038424 €77.00 + vat
Brand : Pichler

Angled adaptor for sliding hammer. Can be used with any of the above universal sets.               

 311146015_(Small).jpg

Part No: 311146015 €22.00 + vat
Brand : Govoni
Denso adaptor for all of the above sliding hammer kits                                     

 ADS0000762_(Small).JPG Part No : ADS0000762 €24.00 + vat
Brand : ADS
Denso adaptor for above sliding hammer Part no: ADS4

 DEA1_(Small).jpg

Part No : DEA1 €69.00 + vat
Brand : Govoni
Special adaptor kit for Denso common rail injectors. Can be used with any of the above universal sets.
Make : Toyota, Lexus
Engine Size : 2.0 D4D, 2.2 D4D, 3.0 D4D
Engine Code: 1KD-FTV, 1AD-FTV, 2AD-FHV
Injector part no : 23670-30080, 08609496

311081000_(Small).JPG 

Part No : 311081000 €57.24 + vat
Brand : Govoni
Special adaptors kit for Denso common rail injectors. Can be used with any of the above universal sets.
Make : Toyota, Lexus
Engine Size : 2.2 D4D
Engine Code : 2AD-FHV
Injector part no : 23670-26011

311081015_(Small).JPG  Part No : 311081015 €36.90 + vat
Brand : Govoni
Special adaptors kit for Denso common rail injector. Can be used with any of the above universal sets.
Make : Nissan
Engine Size : 2.5 DCi
Engine Code: YD25DDTI
Injector part no : MB416600, MB40A, 03J01523

311081017_(Small).JPG 

Part No: 311081017 €36.90 + vat
Brand : Govoni
Special adaptor kit for Denso common rail injector. Can be used with any of the above universal sets.
Make: Opel, Vauxhall
Engine Size: 1.7 CDTi
Engine Code:Z17DTJ
Injector part no: 8-97376270-3, 11L12182

311062000_(Small).JPG  Part No: 311062000 €88.12 + vat
Brand : Govoni
Special adaptor kit for Siemens common rail injectors. Can be used with Injector sliding hammer—Part No : 311026000 and ADS4.  It is already inculded in 311185000

311072010_(Small).JPG  Part No: 311072010 €24.49 + vat
Brand : Govoni
Special adaptor for Siemens Piezo Common Rail Injectors to use with injector sliding hammer - Part No : 311026000 and ADS4. It is already included in 311185000 and 311166000

 311184000_(Small).JPG Part No: 311184000 €303.11 + vat
Brand : Govoni
         
Universal Injector removal kit. Light duty for Denso, Bosch, Siemens and Delphi.  This kit allows you to remove these injectors without dismantling injector internals.There are two different connection systems depending on the injector, one connects to the fuel inlet connection and the other option clamps around the injector body.

 311169000_(Small).JPG   Part No : 311169000  €352.50 + vat
Brand : Govoni
Universal set for removing seized Denso injectors.
Works with small sliding hammer supplied with kit and can also use with large Govoni sliding hammers 311026000, 311185000 and Govoni universal kit 311166000 and ADS4.
Denso injectors are fitted to a large range of brands including : Toyota, Lexus, Nissan, Mazda, Opel, Ford.  

270019000_(Small).JPG  Part No : 270019000 €303.90 + vat
Brand : Govoni
Hydraulic piston for Injector removal, 12 tonne. Also has many other uses.                  

 270020000_(Small).JPG

Part No : 270020000 €354.50 + vat
Brand : Govoni

Hydraulic piston for Injector removal, 20 tonne. Also has many other uses.

 271004000.jpg Part No : 271004000 €350.00  + vat
Brand : Govoni

Hydraulic hand pump set, developing 700 bar pressure, use with Pichler and Govoni Hydraulic piston.
Includes the correct fitting for Govoni and Pichler pistons.

80254000_(Small).JPG      Part No : 80254000 €45.12 + vat
Brand : Govoni
Porta power hand pump conversion adaptor
Allows you to use your existing Porta power hand pump with the injector removal pistons
Most standard Porta powers have the incorrect fitting to connect to the piston.

Engine specific Injector Removal Tools

Note all of the following Injector removal tools are listed alphabetically in engine brand order and then in engine size smallest to largest

Examples of engines fitted to different brand cars:
Alfa Romeo = Alfa Romeo
BMW = BMW, Landrover, MG-Rover, Mini
Fiat = Fiat, Alfa Romeo, Lancia, Opel, Saab, Suzuki
Ford = Ford, Mazda, LDV, Jaguar
Opel = Opel, Vauxhall, Chevrolet, Daewoo, Saab
PSA = Peugeot, Citroen, Mini, Ford, Mazda, Volvo, Landrover, Jaguar, Suzuki
Renault = Renault, Nissan, Opel, Dacia, Suzuki

As you can see there are a great amount of variations so it is important to know your engine brand type and engine code when looking up your injector removal tools.
 

 

Any of these sets that use the hydraulic piston will also need a hydraulic hand pump - see above part no 271004000
Extraction Type : Hydraulic (This only applies if you have the Hydraulic attachments or purchase them separately or if they are included in the kit you are purchasing)

311055015_(Small).jpg 

Part No : 311055015 €445.00 + vat
Brand : Govoni

Common Rail Injector removal tool set for removal of seized Injectors on BMW engine vehicles
Includes injector seat cleaner/cutter tool and blower tool.
Extraction Type: Mechanical
Makes :
BMW, Land Rover, MG Rover
Engine size
2.0D, 2.5D, 3.0D
Engine codes: M47TU, M57, M57TU

311093000_(Small).JPG  Part No : 311093000 €483.76 + vat
Brand : Govoni
Complete set for removing seized injectors on Fiat multijet engine vehicles.
Extraction Type: Hydraulic or Mechanical
Makes:
Alfa Romeo, Fiat, Lancia, Opel, Saab, Suzuki
Engine sizes : 1.3, 1.6, 1.9, 2.0, 2.3, 3.0 multijet and CDTi and DDIs

311023000_(Small).JPG 

Part No : 311023000 €168.19 + vat
Brand : Govoni

Common Rail Injectors removal tool set for removal of seized injectors on Mercedes CDi engines where space is limited
Extraction Type: Mechanical
Mercedes : CDi engines

 

311032000_(Small).JPG  Part No : 311032000 €98.84 + vat
Brand : Govoni
Common Rail Injectors removal tool set for removal of seized Injectors on Mercedes CDi engines.
Extraction Type: Mechanical
Mercedes
: Sprinter, Vito, Viano, Vario
Engine Sizes : CDi

311064000_(Small).JPG  Part No : 311064000 €155.00 + vat
Brand : Govoni
Common Rail Injectors removal tool set for removal of seized injectors on Mercedes CDi engines that use Delphi injectors eg. Mercedes and Ssangyong.
Extraction Type: Mechanical

 311171000_(718x800).jpg Part No : 311171000  €280.00 + vat
Brand : Govoni
This kit allows for removal of the tightly seized injectors on Mercedes CDi engines including the V6
Mercedes: Sprinter, Vito, Viano, Vario, CLK , CLS, GLK, GL, C Class, E Class, M Class, S Class, R Class, G Class
Chrysler :  300 C
Engine Sizes :  2.1, 2.2, 3.0V6 CDI

 311179000_(Small).JPG

Part No: 311179000 €122.94 + vat
Brand : Govoni
This kit allows for removal of seized injectors on Mercedes engines with new type Delphi injectors
Extraction type : Mechanical
Mercedes: Various models
Chrysler : Various models
Engines Sizes : 2.1 CDI
Engine Codes : OM651
Works with the included small sliding hammer but can also be used with any of the above universal sliding hammers.

 ADS0001007_(Small).JPG

Part No : ADS0001007 €75.00 + vat
Brand : ADS
This kit allows for removal of seized injectors on Mercedes engines with new type Delphi injectors
Extraction type: Mechanical
Mercedes : Various models
Chrysler : Various models
Engine Sizes : 2.1 CDI
Engine Codes : OM651
Works with the universal sliding hammer, Part No : ADS4. Can be used with all the other universal kits when you add an optional adaptor to it.

 ADS0001254_(Small).JPG

Part No : ADS0001254 €680 + vat
Brand : ADS
PSA HDI Injector removal tool
Complete set for removing seized injectors on PSA engine vehicles
Extraction Type : Hydraulic
Makes: 2.0, 2.2 HDi - Citroen, Peugeot, Suzuki, Fiat,
Makes: 1.6 HDi - Citroen, Peugeot, Ford, Mazda, Volvo, Mini
Engine Sizes: 1.6, 2.0, 2.2 HDi
Engine Codes: DW10ATED4 / RHS, DW12TED4 / 4HX, 9HX, 9HY, 9HZ, 9HV and some others

 ADS0001076_(Small).JPG

Part No : ADS0001076 €61.68 +  vat
Brand : ADS
PSA 8 valve plate
Extra frame and parts to add to injector removal kit part no ADS0001254 allowing you to use on the following PSA engine vehicles
Extraction Type: Hydraulic
Makes: Citroen, Peugeot, Suzuki, Fiat
Engine Sizes: 2.0 HDi
Engine Codes: RHZ, RHY

311056000_(Small).JPG  Part No : 311056000 €275.18 + vat
Brand : Govoni
Common Rail Injector removal tool set for removal of seized Injectors on PSA engine vehicles. 
Extraction Type: Mechanical
Makes: Peugeot, Citroen, Suzuki, Fiat 
Engine Size
: 2.0 HDi 16v, 2.2 HDi 16v
Engine Codes: DW10, DW12

 SFPSA_(Small).JPG Part No : SFPSA €103.74 + vat
Brand : Govoni
Special supports for injector remover to be used on PSA 2.0 & 2.2 HDi engines—to be used with set 311070000 also can use with Hydraulic puller kit Part No 311116000
Extraction Type: Hydraulic or Mechanical
Makes
: Citroen, Fiat, Peugeot
Engine Sizes
: 2.0 16v, 2.2 HDi 16v
Engine Codes : RTH, RHW, 4HW, RHT, RHM, RHR, RHK 
 

 311071000_(Small).JPG Part No: 311071000 €98.28 + vat
Brand : Govoni
Common Rail Injectors removal tool set for removal of seized Injectors on Renault engine vehicles.
Extraction Type: Mechanical
Renault:
Clio, Fluence, Kangoo, Laguna, Megane, Modus, Scenic, Twingo
Nissan
: Almera, Kubistar, Micra, Note, Quashqai, Tida
Engine Sizes : 1.5 DCi

 123_311140000.jpg

Part No : 311140000  €410 + vat
Brand : Govoni
Set for removing seized injectors on Renault engine vehicles. Includes long shaft for using with hydraulic piston (not shown in picture)
Extraction Type : Hydraulic or mechanical
Makes : Renault, Nissan, Opel
Engine Sizes: 1.9 DCi, 1.9 CDTi
Engine codes: F9Q
Can be used with hydraulic piston - Part No : 270019000

 ADS0000806.._(Small).JPG Part No : ADS0000806 €850.00 + vat
Set for removing seized injectors on Renault engine vehicles for Bosch Pizo injectors.  Also included in the set are parts allowing you to remove the nozzle holder from the cylinder head if it breaks off when removing the injector.
Extraction Type : Hydraulic
Makes : Renault, Nissan, Opel
Engine Sizes : 2.0, 2.3DCi
Engine Codes : M9R, M9T

 ADS0001075_(Small).JPG Part No : ADS0001075  €140.42 + vat
Optional extra kit for  Bosch coil type injectors to be used with above M9R kit Part No - ADS0000806
  

 ADS7.._(Small).JPG

Part No: ADS7 €498 + vat
Brand : ADS
To be used with 311166000 Govoni universal set
Solutions for removing Bosch Piezo and Bosch coil type injectors when the top is broken off or when it leaves the nozzle holder behind in the head. For Renault 2.0 DCi M9R & M9T
Includes: 
Special twist socket
Blank for hole in cylinder head
Blank insertion rod
M16 x 1.5 long tap
M16 x 1.5 spiral flute tap and extension M17 x 0.75 long tap
M16 x 1.5 special rod
M17 x 0.75 special rod
Tap extension

Makes : Renault, Nissan, Opel
Engine Sizes : 2.0, 2.3 DCI
Engine Codes : M9R, M9T

 ADS0001121_(Small).JPG

Part No : ADS0001121 €239 + vat
Brand : ADS
On the 2.0 DCI M9R & M9T Renault engine the injector clamp down bolt may sometimes sheer off in the head and this kit is for drilling out and repairing threads in the head. 
Makes : Renault, Nissan, Opel
Engine Sizes : 2.0, 2.3 DCI
Engine Codes : M9R, M9T

 311110000_(Small).JPG Part No : 311110000 €103.74 + vat
Brand : Govoni
Special supports for injector remover to be used on Renault 2.0 DCi and 2.3 DCi engines—to be used with set 311070000 also can use with Hydraulic puller kit Part No 311116000
Extraction Type: Hydraulic or Mechanical

Makes
: Nissan, Opel, Renault
Engine Sizes
: 2.0 DCi
Engine Codes : M9R, M9T 
 

 311070000.jpg

Part No : 311070000 €450.00 + vat
Brand : Govoni
Complete set for removing seized injectors on Renault engine vehicles.
Extraction Type: Hydraulic or Mechanical 
Makes:
Nissan, Opel, Renault
Engine Sizes
: 2.2, 2.5 DCi
Engine Codes : G9T, G9U
See bottom of page for demo video

Various Injector Tools

 FGA345_(Small).jpg Part No : FGA345 €195.00 + vat
Air hammer kit to help loosen seized injectors. Comes with 6 chisels

 311076000_(Small).JPG Part No : 311076000 €110.00 + vat
Used for removal of seized copper washer underneath injector

 IWE_(Small).JPG Part No : IWE  €49.00 + vat
Used for removal of seized copper washer underneath injector, also has variable depth control for different thickness washers

 60390750_(Small).JPG Part No : 60390750      €86.00 +  vat
Optional sliding hammer for part no IWE       

 772001000_(Small).JPG Part No : 772001000 €91.60 + vat
Kit to restore threads M6 on aluminium heads. Ideal for repairing damaged threads on injector clamp down bolt on Merc CDI engines and many others
Set includes:
Special drill bit 9mm
Special tool for screwing in threaded inserts
M6 X 60 hex head bolt
10 threaded inserts (top ups available)

 772001002_(Small).JPG Part No : 772001002 €15.50 + vat
Top up of M6 threaded insert parts for use with part no : 772001000

 IK8MM(Small).JPG

Part No : IK8MM €49.00 + vat
Kit to restore threads M8 on aluminium heads. Ideal for repairing damaged threads on injector clamp down bolt along with other uses.
Set includes :
Special drill bit 11mm
Special tool for screwing in threaded inserts
5 x threaded inserts (top ups available)

 FG190.S5_(Small).jpg Part No : FG190/S5 €174.04 + vat
Special sockets for solenoids of Bosch and Siemens injectors
Comes in 4 sizes:
25mm and 27mm for Siemens injectors
29mm and 30mm for Bosch injectors

 SDC12720_(Small).JPG  Part No : BIVAK       €14.00 + vat
Bosh injector valve special allen key

 ADS0000268_(Small).JPG Part No : ADS0000268  €15.00 + vat
Special tool for opening Denso valves to allow you to screw in an adaptor for injector removal
 

 ADS0001062_(Small).JPG Part No: ADS0001062   €27.00 + vat
Special socket for twisting out Bosch Piezo Injector main body from the cylinder head.
Required when the top of the injector is damaged and you cannot attach the hydraulic puller.
After twisting out the body you will need other tools to pull out the nozzle and nozzle holder separately.

 6038472E_(Small).JPG Part No : ADS3330 €39.00 + vat
Pilot valve and spindle extractor for Bosch coil type injector. This allows you to remove the Pilot valve therefore allowing you to tap down further into the body of the injector so that the injector removal tools get a better grip on the threads

 60383317_(Small).JPG Part No : 60383317 €120 + vat
Special M17 tap allowing you to thread further down into the top of the Bosch coil injector so therefore allowing you to screw the injector removal tools threaded shaft down further into the body of the injector

 FG72_GMM3_(Small).JPG Part No : FG72/GMM3 €16.00 + vat
Tap driver for tap sizes from M5 to M20 for use with the Renault M9R kit and various others

Govoni - Injector Seat Cutting and Cleaning Tools            

311047014_(Small).JPG 

Part No: 311047014 €177.15 + vat
Set of tools for Injectors seat cleaning for Bosch and Siemens Injectors.
Set includes:
17mm ratchet spanner
Blower tool with M10 & M8 thread
Tool for Injector edge resurfacing
Seat cutter for Bosch Injectors - 15.5 mm
Seat cutter for Siemens Injectors - 17 mm
 


 311047017_(Small).JPG Part No : 311047017 €214.20 + vat
Set of tools for Injectors seat cleaning for Bosch and Siemens Injectors.
Set includes :
17mm ratchet spanner
Blower tool with M10 & M8 thread
Tool for Injector edge resurfacing
Seat cutter for Bosch Injectors - 15.5 mm
Seat cutter for Bosch Injectors -17mm -19mm
Seat cutter for Siemens Injectors - 17 mm

 311047025_(Small).JPG Part No : 311047025 €303.60 + vat
Set of tools for Injectors seat cleaning for Bosch, Siemens and Delphi Injectors.
Set includes :
Blower tool with M10 & M8 thread,
Tool for Injector edge resurfacing,
Seat cutter for Bosch Injectors - 15.5 mm
Seat cutter for Bosch Injectors - 17mm - 19mm
Seat cutter for Siemens Injectors - 17 mm
Seat cutter for Delphi Injectors - 17mm
  

 311127000_(Small).jpg

Part No : 311127000 €590.00 + vat
Injector sealing seat cleaning and milling set universal. This is the optimized version of the cleaning and milling tool set. Can be used with diesel direct injection and common rail engines with Bosch, Delphi, Denso and Siemens.
Set includes:
28 pieces:

Injector washer extractor, Flexible brush driver, Main driving mechanism, Holder for brushes, Special wire brushes 17mm, 18mm, 19mm, 21mm, 24mm, 7mm x 2, Polishing brush 25mm x 4, Polishing brush driver, Injector seat cutters 120 deg. 17mm diameter, 180 deg. 15—17 mm diameter, 180 deg. 17 mm diameter, Centralising guides x 3, Cylinder head injector hole blanks x 6, Hole blank insertion ro
d,
Please enquire for more details and options for this set.

 311112000_(Small).JPG Part No : 311112000 €38.52 + vat
Injector seat cleaning for Denso injectors 17 –19 mm
Makes :
Toyota, Mazda, Mitsubishi

311186000_(Small).jpg 

Part No : 311186000 €110.70 + vat
Injector seat cutter for 2.0 TDi PD              
Makes : VW, Audi, Seat, Skoda
 
Engine Code : BKD                                                  

 311047023_(Small).JPG Part No : 311047023 €23.10 + vat
Injector face resurfacing tool                  

 ADS5_(Small).jpg

Part No : ADS5 €169 + vat
Cylinder head injector bore cleaning set. 
When you remove a seized injector the bore in the cylinder head would have a build up of corrosion and rust making it very difficult to refit the new injector, with this set you can clean this in a matter of minutes.
Includes :
8mm  wire brush
18mm wire brush
19mm wire brush
21mm wire brush
24mm wire brush
Brush holder
Flexible drive
Blanking plugs x 4
Blanking plug inserting rod

     

Budget Injector Seat Cutting and Cleaning Tool

 AET-1081_(Small).JPG   Part No : AET-1081   €75.00 + vat
Budget set of tools for Injectors seat cleaning.                                          
Set includes:
Seat cutter  - 15 mm
Seat cutter  - 17 x 17 mm
Seat cutter  - 17 x 19 mm
Seat cutter  - 17 mm angled                    

 

Glow plug removal and repair tools

 FG183.S5_(Small).jpg

Part No : FG183/S5 €68.30 + vat
Brand : Fasano
Special socket for Glow plugs in 5 sizes : 8, 9, 10, 12, 14mm 1/4 drive         

311031000_(Small).JPG 

Part No: 311031000 €297.50 + vat
Brand : Govoni
Kit for removing seized or sheared m10 thread glow plugs. Add on tap and piloted drill bit kit for M8 glow plugs, see part no 311031016
 

 311031016_(Small).JPG

Part No : 311031016 €113.07 + vat
Brand : Govoni

Tap and piloted drill bit kit for M8 thread glow plug. Use with kit for removing seized or sheared glow plugs, part no 311031000

 311031017_(Small).JPG Part No : 311031017 €370.00 + vat
Brand : Govoni
Kit for removing seized or sheared M8 & M10 thread glow plugs

311167000_(Small).JPG 

Part No : 311167000    €972.50 + vat
Brand : Govoni
Master
kit for removing seized or sheared M8x1, M9x1, M10x1, M10x1,25 thread glow plugs. 
Will need to use a ratchet tap holder which is not included in set, see part no FG72/GMC2 -
See bottom of page for demo video 

 FGA332_AN_(Small).JPG

Part No : FGA332/AN €115.00 + vat
90 degree Air Drill. Required when drilling out glow plugs in difficult positions

 734003000_(Small).JPG Part No : 734001000 €44.80 + vat 2.5mm
Part No : 734002000 €44.80 + vat 3.5mm
Part No : 734003000 €44.80 + vat 4mm
Part No : 734004000 €44.80 + vat 5mm
Part No : 734005000 €44.80 + vat 7mm
Brand : Govoni
Roller extractor used for removing glow plug centre electrode.
Available in the above 5 different sizes

 FG72GMC1_(Small).JPG

Part No : FG72/GMC1 €15.00 + vat
Short Ratchet tap holder M3 to M8
Sometimes may need to use with glow plug removal sets
 

FG72-GMC2.jpg  Part No : FG72/GMC2 €15.00 + vat
Short Ratchet tap holder M5 to M12
Sometimes may need to use with glow plug removal sets

 TPG_(Small).JPG Part No : TPG €6.50 + vat
Thread pitch gauge for metric threads  
Required when you need to figure out the thread pitch of the glow plugs you are working on                                 

 374A_(Small).JPG

Part No : 374A €7.00 + vat
Flexible magnet with 7mm head allowing you to fit into the injector hole in the head to fish out metal pieces or glow plug tips 

 5670_(Small).JPG Part No : 5670 €75.00 + vat
Kit for repairing damaged M8 x 1.0 glow plug threads in the cylinder head.
Set Includes :
Special tap M10, Special tap M8, Cylinder head hole reamer, Inserts 11mm long, M10 x 1.0 external diameter, M8 x 1.0 internal diameter x 5
 

 772003000_(Small).JPG Part No : 772003000 €120.00 + vat
Brand : Govoni
Kit for repairing damaged  M9 x 1.0 glow plug threads in the cylinder head. Set includes:
Special tap M12, Special tap M9, Cylinder head hole reamer, Insert driver tool, Inserts 10mm long  M12 x 1.0 external diameter, M9 x 1.0 internal diameter x 6

 5672_(Small).JPG Part No : 5672 €85.00 + vat
Kit for repairing damaged M10 x 1.0 glow plug threads in the cylinder head.
Set includes:
Special tap M12, Special tap M10, Cylinder head hole reamer, Inserts 12mm long, M12 x 1.0 external diameter, M10 x 1.0 internal diameter x 5, Inserts 19mm long, M12 x 1.0 external diameter, M10 x 1.0 internal diameter x 5 
 

 5673_(Small).JPG Part No : 5673 €75.00 + vat
Kit for repairing damaged M10 x 1.25 glow plug threads in the cylinder head.
Set includes:
Special tap M12, Special tap M10, Cylinder head hole reamer, Inserts 12mm long, M12 x 1.25 external diameter, M10 x 1.25 internal diameter x 5
 

 772004000_(Small).JPG Part No : 772004000 €525.00 + vat
Brand : Govoni
Glow plug and spark plug complete thread repair set.
Application Glow plugs : M8 X 1, M9 X 1, M10 X 1, M10 X 1.25, M12 X 1.25
Application Spark plugs : M12 X 1.25, M14 X 1.25
  

Govoni - Glow plug tip removal tools

 311172000.jpg Part No : 311172000 338.00 + vat
Master kit for removing glow plug tip in the cases of where the glow plug screws out and leaves the tip behind suitable for 8mm, 9mm, 10mm x 1.00 and 10mm x 1.25 glow plugs with 2 different size drill bits and two different size taps and tip removal attachments M3 & M4. Will need to use a ratchet tap holder which is not included in set,  see part no FG72/GMC1. 

 311178000_(Small).jpg

Part No : 311178000 €202.56 + vat
Kit for removing glow plug tip in the cases of where the glow plug screws out an leaves the tip behind suitable for 8mm x 1mm glow plugs. Specifically designed for the following makes and models: Citroen, Ford, Mazda, Peugeot and Volvo that are fitted with 1.4 & 1.6 HDi engine. Will need to use a ratchet tap holder which is not included in set, see part no FG72/GMC1


 

  • Above is a list of what we currently stock - others can be ordered on request.
  • To see other Picher and Govoni tools that we stock see our Other Tools and Test Equipment page
  • To see Govoni Timing Tools see the Timing Tools page


     

DEMO VIDEOS

 



 


            
 
Downloads
 
Catalogues Govoni-Catalogue.pdf
Govoni-news-No1.pdf
Govoni-news-No2.pdf
Govoni-news-No3.pdf
Govoni-news-No4.pdf
____________________________________________________________

Designed by: P1 : Digital