The new ATS5004D 4 channel and ATS5000D 2 channel Oscilloscopes, by far the most advanced scopes on the market with user friendly set up.
Atis lite software, a database is available with more than 250 automotive components with more than 400 diagnostic measurements, more generic guided tests and preset screens than any other scope on the market, covering everything from canbus to battery drainage test.
Atis pro software, detailed vehicle specific info, allowing you to search by specific vehicle giving you all of the below information:
Wiring diagrams Specific sensor and actuator tests Procedures and sample wave forms Live connection diagrams Component location information with live pictures Technical information about the specific item you are testing
This level of information on a scope has never been available before.
Motor management systems in cars get more and more sophisticated. When these sophisticated systems malfunction, sophisticated measuring equipment is required to locate the cause of the problem. With the ATS Automotive Diagnostics Kit, the automotive specialist obtains all necessary tools to perform most of the diagnostic tests to locate the problem, all conveniently packed in a protective case.
Automotive oscilloscope
Heart of the Automotive Diagnostics Kit is the Automotive scope ATS5004D automotive oscilloscope. This PC oscilloscope turns your computer into a sophisticated automotive diagnostic system. Equipped with four differential inputs, (also available in 2 channel) the Automotive scope ATS5004D guarantees measuring multiple signals without the risk of creating short circuits through the oscilloscope. The compact Automotive scope ATS5004D is USB powered, which makes it easy to connect it to a laptop computer and perform measurements while driving the vehicle. The large input range, the long memory buffers and high maximum sampling rate make it the possible to capture almost any automotive signal. The built in connection test feature on each channel informs whether the test points have electrical connection to test subject, leaving no doubt whether there is no connection or no signal.
Automotive Test and Information System
The ATIS-Pro Automotive Test and Information System is a large knowledge base with information on a huge range of electrical and electronical components that are used in the motor management system and ABS system of a car. In an intuitive graphical environment background information on sensors and actuators can be found, as well as detailed schematics, diagnosis instructions, component locations with photographs of most available cars and example signals for proper functioning components. The unique point of ATIS is the direct coupling between the diagnosis instructions with the example signals to the measuring instrument. One click of the mouse in ATIS will launch the automotive measurement software and load the specific settings to measure on the particular component. The mechanic can focus on finding the problem, he does not need to find out how to setup the instrument.
The Automotive Diagnostics Kit is delivered with ATIS-Lite. As an extension to ATIS-Lite, ATIS-Pro can be ordered. ATIS-Pro contains an extensive database with more schematics, connection diagrams and oscilloscope settings with reference signals.
Measuring leads
To connect the Automotive scope ATS5004D to the automotive circuits, the Automotive Diagnostics Kit contains a set of four special measuring leads (or 2 if buying 2 channel). The Measuring Leads are 3 meter long low noise BNC to 4 mm banana measuring leads, specifically designed to be used on differential oscilloscope inputs. The two ends of the Measuring leads with the banana jacks can be placed 2 meters apart, without picking up external disturbances. The length of 3 meter allows to connect the instrument to components under the hood while the instrument is located on the passenger seat, making it possible to perform measurement while driving. The measuring lead is made of silicone, making it heat resistant and oil resistant, perfectly suitable for automotive applications. The 4 mm banana jacks make it possible to connect a variety of test points or clamps.
Back probes
The Automotive Diagnostics Kit contains a set of back probes. These thin and flexible measuring probes fit on any test lead with 4 mm banana jacks and make it possible to connect to hard to reach places. They allow to back probe wires in connectors, without breaking the circuit, without the need of break out boxes and without damaging the wire isolation. The set contains 8 probes (or 4 probes if buying 2 channel), four black ones, a red, a yellow, a green and a blue one, matching the input channel color coding of the Automotive scope ATS5004D.
Ignition pickups
To measure secondary ignition signals, the Ignition Pickup Set is added to the Automotive Diagnostics Kit. Simply clamp the Ignition PickupSet around a spark plug cable and measure the secondary ignition signals, both from normal ignition systems and DIS ignition systems. The Automotive Diagnostics Kit contains two pickups. (see optional COP testing adaptor)
Current clamps
To measure large currents, like e.g. starting currents, a current clamp CC-600 is included in the Automotive Diagnostics Kit. The Current clamp CC-600 makes it possible to measure current with your automotive oscilloscope, without the need of breaking the circuit. Simply clamp the Current clamp CC-600 around the wire and measure the current, up to 600 A. Current measurements can reveal problems that with a voltage pattern remain hidden, like e.g. compression problems that are visible in the starting current.
Many components draw far less than 600 A, making the 80 A current clamp CC-80 a more suitable current clamp. It will measure up to 80 A, giving a much higher accuracy at low currents than the Current clamp CC-600. Use it to reveal problems in driving injectors, measuring leakage currents etc.
Accelerometer and manual trigger button
The dual accelerometer measures accelerations up to 2 g in two planes. It can be used to measure vibrations in mechanical systems, but is can also be used to determine the maximum power of an engine, without the need of expensive equipment. Attach the acceleration sensor to the floor of the car and accelerate at full power. Using the weight of the car and the measured signal, the power can then be calculated by the software.
The manual trigger button can be used to trigger the automotive oscilloscope when the input signals are unknown. Connect the automotive oscilloscope to the sensors you want to check and start driving the car. As soon as the problem occurs, e.g. the engine holding back, press the manual trigger button. The automotive oscilloscope will now measure the signals and store them. Since the oscilloscope can store the signals before pressing the trigger button, later examination of the signals will show how the problem developed.
The manual trigger button can be used independently from the accelerometer.
Differential attenuators
The 80 Volt full scale input range of the Automotive scope ATS5004D makes it possible to measure almost any automotive signal. In case the voltage exceeds 80 Volt, the Differential attenuatorcan be used. This special differential attenuator attenuates the input signal by a factor 10. It can be used when measuring e.g. primary ignition signals or fuel injector signals. The Automotive Diagnostics Kit contains a Differential attenuatorfor each channel.
Part No: ATS5004D€2,295.00 + vat
4 Channel Oscilloscope
Includes: ATIS lite software 4 Channel Scope unit 4 x measuring leads 3 meters long 8 x colour coded back probs 2 x secondary ignition pick ups 1 x current clamp 600 amp 1 x current clamp 80 amp 4 x differential attenuators Accelerometer Manual trigger button Carry Case
Part No: ATS5000D €1,795.00 + vat
2 Channel Oscilloscope Includes: ATIS lite software 2 Channel Scope unit 2 x measuring leads 3 meters long 4 x colour coded back probs 2 x secondary ignition pick ups 1 x current clamp 600 amp 1 x current clamp 80 amp 2 x differential attenuators Accelerometer Manual trigger button Carry case
Optional Extras
Part No : ATIS Pro €495.00 + vat
Automotive car brand software with more than 4000 models with electric diagrams, system and component explanation, how to hook up test leads, pre scope adjustments and reference signals.
Part No : RFS400€560.00 + vat
Allows you to test common rail return flow while driving / under load and displays the readings through the software. Includes : flow meter, 4 pipes and different connections for Bosch, Delphi, Siemens and Denso injectors
Part No : APS260€248.00 + vat
Absolute pressure measurement system. Allows you to measure vacuum and pressure for example turbo boost pressure, turbo control valves, map sensors, exhaust pressure pulsations etc.
Part No : COP adaptor €75.00 + vat
Allows you to test coil on plug systems
OSCILLOSCOPE AND MULTIMETER TEST LEADS AND ACCESSORIES
A Master Set of premium Waekon Gold Test Leads, Jumper Leads and Probe Tip.Accessories for DVOMs, lab scopes used for general circuit testing, organised in a rugged plastic case.Designed to fully address the circuit testing needs of the automotive service professional.
Provides a fast, reliable way to pinpoint test relay circuits located in the underhood relay/fuse junction box.
Extends the relay away from the junction box.
Provides the ability to test the circuit live with the relay in place.
It acts like a mini breakout box for pinpoint testing relay circuits.
Includes:
2 large relay spade terminal extensions
6 medium relay spade terminal extensions
5 small relay spade terminal extensions
1 plastic storage case
Testing is done without wire piercing, removing the junction box for back probing or trying to find the proper wires in the harness bundle that exits the box.
The Perfect Mate Probe Adapter Tips are designed to be a perfect fit for most automotive connector pins.They work great for “hands free” jumper wire testing.The Tee Connection Adapter provides a solid connection for road testing.It acts like a universal breakout box for virtually any 2 or 3 pin connector on the vehicle.
The Perfect Mate Probe Adapter Tips are designed to be a perfect fit for most automotive connector pins.They work great for “hands free” jumper wire testing.The Tee Connection Adapter provides a solid connection for road testing.It acts like a universal breakout box for virtually any 2 or 3 pin connector on the vehicle.
.JPG', '420', '480'))
.jpg', '640', '280'))
.jpg', '640', '288'))
.jpg', '93', '36'))
.jpg', '94', '79'))
.jpg', '94', '101'))
.jpg', '93', '81'))
.jpg', '94', '37'))
.jpg', '91', '53'))
.jpg', '93', '121'))
.jpg', '92', '19'))
.jpg', '94', '28'))
.JPG', '404', '480'))
.JPG', '416', '480'))
.JPG', '640', '144'))
.JPG', '434', '480'))
.JPG', '640', '586'))
.JPG', '480', '480'))
.JPG', '388', '480'))
.JPG', '306', '480'))
.JPG', '640', '598'))
.JPG', '640', '581'))
.JPG', '358', '480'))
.jpg', '640', '371'))
.jpg', '640', '277'))
