RyansAutomotive.ie

CarScope i-Tester Master Kit

305.00 ex. VAT

CarScope i-Tester Master Kit

Available on back-order

Product Description

CarScope i-Tester Master Kit

CarScope i-Tester is essentially a specialized type of engine analyser. It is a complex, multi-function tool, which can help diagnosing the engine and finding engine problems. I-Tester could be used with both gasoline and diesel-powered vehicles. Currently, there are 2 modes available: Relative compression test and Common Rail pressure test, but several automated diagnostic tests are upcoming with a future firmware updates!

No oscilloscope knowledge skills needed. You can skip the training and set-up time of an ordinary oscilloscope and get directly to a quick, precise engine analysis;

This master set adds the most necessary accessories in suitable plastic tool case with black EVA foam.

Relative compression test
This test is only a comparison between cylinders so we can use this method to “see” if we have a cylinder (s) with low compression by comparing one cylinder to the next. Hence the term “relative”.
Relative compression is the fastest, simplest way to find a low compression cylinder. This test has previously been available only on large and expensive diagnostic systems, requiring a laptop and an oscilloscope. Now it is easier than ever — with the new CarScope i-Tester that combines both functions – relative compression test and automatic waveform analysis. So, the final results are displayed in an easy to understand format.
You do not have to check each individual cylinder, all cylinders can be tested in one go. CarScope i-Tester works on 3, 4, 5, 6, 8, 10, 12-cylinder cars, 4 stroke, diesel and gasoline engines, DIS, conventional and Coil-on-Plug systems, and 12V electrical systems.
Cylinder synchronisation

By hooking up a second probe to either the ignition or an injector, you can follow the firing order/injection sequence and know which one it is. This is not the only way to do this type of cylinder identification but it does work as a way to start with.

Common Rail pressure test NEW!
This new function is available since firmware version TT0106B (download link)!
This mode is used for fast verification of the condition of the diesel Common Rail high-pressure system. Results allow direct/indirect identification of common problems in this system – lack of pressure due to leaks, high-pressure pump failure, bad high-pressure sensor, no sensor power supply etc.
The principle of this test is based on checking the high-pressure sensor readings while the car is in ignition on, cranking, idling and accelerating states.
Checking the high-pressure sensor readings is the fastest, simplest way to find a problem in the Common Rail system.
This test is very easy to perform – only one wire hooked to the high-pressure sensor output.

Advantages:

• Non-invasive test;
• Test completes within seconds;
• You do not need a pressure transducer to run the relative compression test;
• No mechanical work needed. No removal of spark plugs, glow plugs, or injectors, thus preventing accidental damage to the customer’s           engine components. All you have to do is to disable the fuel system to prevent the engine from starting;
• Disabling fuel system is always better because you are not flooding your cylinders;
• No oscilloscope needed;
• Reduced skill level required and thus achieve rapid testing;
• No waveform analysis skills needed;
• Test based on scientifically grounded theory;
• Test proven in the practice for many years;
• Useful tool in the parking lot type situation instead of dragging a scope/laptop around;
• No current clamp needed, in case the DC voltage method is used

Features:

• 2.4″ TFT LCD 320х240
• no external power adapter needed
• 3 Channel — 3 measurement channels provide the ability to use a variety of voltage and current probes at the same time.
• Protection against reverse polarity connection
• The Relative Compression mode helps you quickly find a low compression cylinder
• Relative compression test function and automatic waveform analysis
• Ultra fast boot time
• Simple to use and connect, easy to use keyboard.
• Internal Micro SD card to save and review measurements
• Works on 4 stroke, diesel and gasoline engines;
• Works on 3, 4, 5, 6, 8, 10, 12-cylinder cars
• Works on DIS, conventional and Coil-on-Plug ignition systems;
• Only 12V electrical systems supported.
• Excellent industrial design

Applications:

Reasons to perform a relative compression test using i-Tester:
Compression test has to be performed when the engine symptoms are as follows:

  • engine misfiring;
  • rough idle;
  • loss of power over time;
  • unexplained loss of power;
  • smoke from the exhaust;
  • puffing noise in induction or exhaust

Checking the engine health in cases as follows:

  • In case of buying a used car;
  • Before ECU remapping to evaluate engine status;
  • Periodic prevention check;
  • In cases where it is very hard to gain access to the spark plugs or glow plugs in order to perform a traditional compression test.

In the set:

  • CarScope i-Tester main device
  • Power supply cable
  • Universal probe with one 4mm banana
  • micro SD memory card
  • Guide book
  • 5mm pluggable terminal block, 2P
  • Plastic case with EVA foam
  • CarScope i-Tester OBD2 cable
  • Inductive Pickup clamp
  • Voltage attenuator 10:1
  • Back-pinning probe x 2
  • Insulated crocodile clip (Red)
  • 10:1 attenuator adapter for synchronization from injectors or ignition primary, Click here to see in store

Optional accessories:

  • Car cigarette lighter cable allowing you to power the device and do relative compression test from the seat of the vehicle
  • Automotive needle probe set
  • AC/DC Current Clamp CA-60 for synchronization from injectors or ignition primary current
  • AC/DC Current Clamp CA-600 for doing relative using starter current draw

Enquire for prices and information on the optional accessories

Important note: Because of lithium-ion battery shipping restrictions, we do not include CR2032 lithium-ion battery inside in the post packages! When you receive the tester, you have to buy a Li-Ion battery type CR2032 yourself and put it into battery holder socket inside the CarScope i-Tester. To do so, you should unscrew and remove four screws to open the bottom cover. We apologize for the inconvenience!

Product Specifications

Weight 2 kg
Dimensions 35 × 30 × 8 cm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

If you want to ask a pre-sale question about this product, please feel free to use the form below.


Your First Name (required)

Your Phone (required)

Your Last Name (required)

Your Email (required)

Your Question